橡膠輸送帶在運行過程當中經常會接觸到許多物料，時間長了之后輸送帶表面容易留下一些不好去除的污漬。污漬日積月累可能會將一些物料黏住，從而影響輸送帶的輸送速度，嚴重的甚可以造成輸送帶跑偏。因此輸送帶是需要定期清洗與維護的。下面，廣州擎川橡膠給大家介紹一種比較簡單的輸送帶清洗方法。
Rubber conveyor belt in the process of operation will often contact with many materials, after a long time, the surface of the conveyor belt is easy to leave some stains that are not easy to remove. The accumulation of stains may stick some materials, which will affect the conveying speed of the conveyor belt, and even cause the conveyor belt deviation. Therefore, the conveyor belt needs regular cleaning and maintenance. Next, Guangzhou Qingchuan rubber introduces a relatively simple cleaning method for conveyor belt.
，在清洗輸送帶前，所有不能涉水的設備都要用塑料薄膜包裹，防止進水造成電機短路，因?yàn)樵O(shè)備浸泡在水中后不能使用。
First of all, before cleaning the conveyor belt, all the equipment that cannot Wade should be wrapped with plastic film to prevent short circuit of the motor caused by water, because the equipment cannot be used after being immersed in water.
第二步、關閉蒸汽閥，查看張緊裝置，調整設備壓力。
Second, close the steam valve, check the tensioning device and adjust the equipment pressure.
第三步、檢查一下輸送帶清洗機的狀態情況，查看一下橡膠輸送帶的情況。如果輸送設備上有零件損壞，必須提前修理好再清洗，否則會影響零件的使用。
The third step, check the status of the conveyor belt cleaning machine, check the situation of the rubber conveyor belt. If there are parts damaged on the conveying equipment, it must be repaired and cleaned in advance, otherwise the use of parts will be affected.
第四步、在清洗輸送帶之前先將輸送帶浸泡一會兒，清洗時會更加方便一些。
The fourth step, before cleaning the conveyor belt, soak the conveyor belt for a while, cleaning will be more convenient.
第五步、用低壓噴槍均勻噴灑攪拌均勻的清洗液。千萬不要使用高壓噴槍，因?yàn)樗鼤?huì)損壞輸送皮帶的表層。沖洗噴槍時，注意不要重復沖洗同一位置，并確保皮帶的每個位置都可以沖洗。
The fifth step is to evenly spray the mixed cleaning solution with a low-pressure spray gun. Never use a high pressure spray gun as it will damage the surface of the conveyor belt. When flushing the spray gun, pay attention not to repeatedly flush the same position, and ensure that each position of the belt can be flushed.
第六步、上述操作完成后，用清水清洗皮帶，檢查皮帶上的污漬，并干燥皮帶以防發霉。
Step 6. After the above operation, clean the belt with clean water, check the stains on the belt, and dry the belt to prevent mildew.
總之，無論哪種設備都必須定期清洗，以保證長期使用，同時不會影響設備的工作效率。
In short, no matter what kind of equipment must be cleaned regularly to ensure long-term use, and will not affect the efficiency of the equipment.
Today is the content of electric torque wrench introduced by Xiaobian. Please pay more attention to our website: http://www.cnbeilibao.com We will update the follow-up content regularly!
